Air Conditioning & Heating · Dallas–Fort Worth, TX
Heating Services in Dallas, TX: Furnace and Heat Pump Repair
Fix a furnace or heat pump that will not heat, with same day help for urgent calls and a written flat rate quote.
- Licensed & insured
- Upfront flat-rate pricing
- Same-day appointments
Need it handled today? Call +1 (614) 756-0643 · book online by email
Quick answer
Heating service in Dallas covers furnace repair, heat pump repair, furnace cleaning and tune ups, and heating system replacement. If your furnace will not heat, check the thermostat, the air filter, the breaker and the gas valve, and never relight a pilot if you smell gas. Leave and call Atmos Energy or 911 from outside. Plumber Service TX repairs and installs furnaces and heat pumps across Dallas and Fort Worth, with same day appointments for urgent no heat calls wherever possible and a written flat rate quote first.
Furnace Problems and Fixes
| Symptom | Likely cause | Fix |
|---|---|---|
| No heat | Thermostat, tripped breaker, failed igniter, flame sensor, gas valve, blower | Check settings and breaker, then diagnose |
| Blows cool air | Dirty flame sensor, high limit, dirty filter | Clean sensor, replace filter |
| Short cycling | Overheating, dirty filter, bad sensor, oversized unit | Replace filter, diagnose |
| Strange noises | Blower, belt, loose panel, ignition delay | Inspect and repair |
| Weak airflow | Filter, blower, duct problems | Replace filter, clean blower, check ducts |
| Yellow burner flame or soot | Combustion problem | Turn off and call right away |
| High bills | Old unit, leaky ducts, dirty system | Tune up, seal ducts, evaluate replacement |
Heat Pump Repair and Installation
A heat pump cools in summer and heats in winter by moving heat, and it can be very efficient in a Texas climate with mild winters. Common problems include a frozen outdoor coil, a failed reversing valve, low refrigerant, a bad defrost board and weak auxiliary heat. Repair when the system is under about 10 to 12 years old and the problem is a single part. Consider a heat pump when replacing an AC and furnace together. See AC installation and replacement.
Need it handled today? Call +1 (614) 756-0643 · book online by email
Furnace Tune Up and Cleaning
- Inspect the heat exchanger for cracks
- Clean the burners, flame sensor and igniter
- Test the gas pressure, safety switches and thermostat
- Check venting and carbon monoxide levels
- Replace or clean the filter and clean the blower
- Inspect ducts and airflow
A fall tune up finds problems before the first cold snap. Carbon monoxide detectors should be on every level. See smoke and CO detectors.
Repair or Replace Your Furnace?
- Repair a furnace under about 15 years old with a single failed part.
- Replace if it is over 15 to 20 years old, has a cracked heat exchanger, or repair costs approach half of a new unit.
- Replace if efficiency is low and bills are high, but weigh the savings against the cost.
A cracked heat exchanger is a safety issue because it can leak carbon monoxide. We will tell you if the unit should not run.
Heating Services Across Dallas Fort Worth
We serve Dallas and the surrounding area, including Fort Worth, Arlington, Frisco and Southlake. Related: thermostats, duct services and gas line services. Email service@plumberservicetx.com or call +1 (614) 756-0643.
How Home Heating Works in North Texas
North Texas winters are short and mild compared with most of the country, but they include cold snaps, freezes and the occasional ice storm. Heating systems sit idle for much of the year, then run hard for a few weeks. That pattern has a downside: parts that rarely run can fail when finally needed, and homeowners often forget routine checks until the first cold morning. Understanding the main systems helps you plan.
Gas furnaces
A gas furnace burns natural gas in a burner assembly, passes hot gases through a heat exchanger, and blows house air across the outside of the exchanger. The combustion gases exit through a flue or vent pipe. Furnaces are rated by AFUE, the share of fuel energy that becomes heat. Older furnaces are around 80 percent efficient, while high efficiency condensing models reach 90 to 98 percent and vent through plastic pipe. A furnace has an ignition system, a flame sensor, a gas valve, a draft inducer, limit switches, a blower and a control board.
Heat pumps
A heat pump is an air conditioner that can run in reverse, moving heat from outdoor air into the house. In the mild Dallas Fort Worth climate, heat pumps deliver two to four times the heat energy per unit of electricity used, and they are a leading choice for new systems. When the temperature falls near freezing, many heat pumps use electric resistance strips as supplemental or emergency heat, and the outdoor coil goes through a defrost cycle.
Electric furnaces and strip heat
Resistance heating converts electricity directly to heat. It is simple and reliable, with high operating costs compared with a heat pump.
Dual fuel systems
A heat pump paired with a gas furnace uses the heat pump when it is efficient and the furnace on the coldest days.
Boilers and radiant systems
Less common here, but present in some homes. Service may require a specialist, so ask us about your equipment.
Furnace Safety: Carbon Monoxide, Gas and Fire Risks
A furnace combines fuel, flame, electricity and moving parts, so safety is part of every service. Three risks deserve attention.
- Carbon monoxide. A cracked heat exchanger, a blocked flue or a poorly adjusted burner can release carbon monoxide into the home. It is odorless. Install CO alarms near bedrooms and on each level, test them monthly and replace them as recommended. Symptoms such as headaches, dizziness, nausea or confusion that improve when you leave the house are a warning.
- Gas leaks. A loose connection, a failing gas valve or a damaged line leaks gas. If you smell gas, leave the home and call Atmos Energy or 911 from outside. See gas line services.
- Fire. Combustible materials stored near a furnace, a clogged flue and overheated components can start fires. Keep the area around the furnace clear, and do not store paint, gasoline or cleaning chemicals nearby.
During a tune up we inspect the heat exchanger, test combustion gases, check the venting, test safety switches and check the gas pressure. If a part is unsafe, we turn the furnace off and tell you why, with evidence.
The Furnace Tune Up: What a Proper One Includes
| Step | What we check | Why it matters |
|---|---|---|
| Visual inspection | Cabinet, wiring, burners, flue and filter | Spots damage, corrosion, loose connections and blockages |
| Heat exchanger | Cracks, rust and warping, with a camera if needed | A cracked exchanger is a safety hazard |
| Burners and flame | Clean burners, a steady blue flame, correct ignition | Ensures clean combustion |
| Flame sensor and igniter | Clean the sensor, test the igniter | Prevents most no heat lockouts |
| Gas pressure | Inlet and manifold pressure | Correct gas input and safe combustion |
| Draft inducer and venting | Operation, pressure switch, flue condition | Safe exhaust of combustion gases |
| Blower and airflow | Wheel, motor, capacitor, static pressure and temperature rise | Efficient heat delivery, no overheating |
| Limit and safety switches | Test shutoffs | Protects against overheating and fire |
| Thermostat and controls | Calibration, wiring, staging | Correct operation |
| CO test | Measure CO at the vent and supply | Verifies safe operation |
A written report with readings follows. If a part is near the end of its life, you will know before it fails in a freeze.
No Heat? A Troubleshooting Guide for a Cold Morning
- Check the thermostat. It must be on heat, set above the room temperature, with fresh batteries if it uses them.
- Check the breaker for the furnace and the air handler, and the furnace service switch, which looks like a light switch near the unit.
- Check the filter. A very dirty filter can shut a furnace down.
- Look at the furnace. A blinking light on the control board indicates a code, and the label on the door explains it.
- Check that the gas valve is open, with the handle parallel to the pipe.
- Listen for the draft inducer fan, then the clicking of the igniter. If it tries and fails repeatedly, the igniter, sensor or gas supply may be the problem.
- Do not try to light a standing pilot unless the label on the furnace gives clear instructions, and never if you smell gas.
- If these steps do not solve it, call. Tell us the code you see, and what you have tried.
Heat Pump Problems and Defrost Cycles
Heat pumps behave differently from furnaces, and some behavior is normal. During cold, damp weather, frost forms on the outdoor coil, and the system periodically goes into defrost mode. The outdoor fan stops, the system reverses, and steam or water vapor rises from the unit. The indoor system may blow cooler air for a few minutes, and electric heat strips may come on to make up the difference. This is normal. Abnormal signs include a unit encased in ice, long or constant defrost, no heat at all, loud noises, and a very high electric bill.
- Thermostat settings. Raising the temperature by several degrees at once can trigger expensive strip heat. Raise it a degree or two.
- Auxiliary heat light. If it is on all the time, the heat pump may not be keeping up, or it may be failing.
- Reversing valve. A failed valve blocks heating or cooling.
- Defrost control board and sensors. Failures cause icing.
- Refrigerant leaks. Reduce capacity and cause ice.
- Airflow problems. A dirty filter or coil reduces performance.
Furnace Replacement: When and What to Choose
A furnace is a long lived appliance, with a typical life of 15 to 20 years, and many last longer. Replacement makes sense when the heat exchanger is cracked, the furnace is old and unreliable, repairs approach half the cost of a new unit, or you want better efficiency or comfort. When choosing a replacement, consider these points.
- Efficiency. Mid efficiency models are about 80 percent AFUE. High efficiency condensing models are 90 percent or more. In a mild climate with few heating degree days, the extra cost of the highest efficiency may take a long time to pay back.
- Staging and blower. Two stage heat and a variable speed blower improve comfort, reduce noise and pair well with a modern AC.
- Sizing. A load calculation avoids oversizing. An oversized furnace short cycles and wears out.
- Venting. Condensing furnaces use plastic vent pipe and need a condensate drain.
- Matching with the AC. If the AC is also old, replacing both together saves cost and ensures compatibility. See AC installation and replacement.
- Heat pump alternative. In many homes, a heat pump can replace both a furnace and an AC.
Preparing Your Home for Winter
- Schedule a furnace tune up in October or November.
- Change the filter, and keep spares on hand.
- Test carbon monoxide and smoke alarms. See smoke detectors.
- Seal drafts around windows and doors, and add attic insulation. See attic insulation.
- Insulate exposed pipes and know where your main water shutoff is. See burst pipe repair.
- Make sure the outdoor unit is clear of debris and ice, if you have a heat pump.
- Have a plan for a power outage, such as a generator. See whole home generators.
- Keep your thermostat at a steady, moderate setting.
Furnace Error Codes: What the Blinking Light Means
Most modern furnaces have a small window on the front, where an LED blinks a pattern. Each pattern is a diagnostic code, and a chart on the door explains it. The details differ by brand, but these families are common.
| Code idea | Typical meaning | Common cause |
|---|---|---|
| Steady light | Normal operation | No problem |
| Slow flash | Normal standby or no call for heat | No problem |
| Two flashes | Pressure switch stuck | Blocked vent, failed inducer, stuck switch |
| Three flashes | Pressure switch open | Blocked flue, condensate drain, failed inducer |
| Four flashes | Limit switch open | Overheating, dirty filter, blower failure |
| Five flashes | Flame sensed with gas off, or reversed polarity | Wiring, gas valve |
| Six flashes | Rollout switch | Blocked flue, cracked heat exchanger |
| Seven flashes | Ignition lockout | Dirty flame sensor, igniter, no gas |
Do not clear a repeated high limit or rollout code without finding the cause. These are safety switches. Resetting them over and over can hide a dangerous problem. Take a photo of the code and send it to us. It speeds up diagnosis.
Furnace Cost Factors: Repairs and Replacement
- Part type. A flame sensor or igniter is a small repair. A control board, inducer motor or blower motor costs more. A gas valve or heat exchanger is a major repair.
- Age of the furnace. Parts are easier to get for newer models.
- Access. Attic and closet furnaces take more time to service.
- Replacement scope. Equipment size and efficiency, venting changes, new gas line, condensate drain, ductwork, thermostat and permits.
- Time of year. Emergency calls on a freezing night cost more at many companies.
A cracked heat exchanger is the main reason a furnace is replaced early. Some manufacturers cover heat exchangers for decades under warranty, so check your documents.
Humidity, Comfort and Static in Winter
Winter air in a heated home can be dry, with humidity falling below 30 percent. Symptoms include dry skin and nose, static shocks, cracked wood and a feeling of cold at a higher temperature than usual. A whole house humidifier on the furnace adds moisture to maintain 30 to 40 percent humidity, which feels warmer and protects wood furniture and floors. Too much humidity causes condensation on windows and mold, so do not exceed what the windows tolerate. Humidifiers need maintenance, such as replacing a water panel each season, and cleaning. Ask us about options. See indoor air quality.
Zoning, Ducts and Even Heat
Two story homes in North Texas often have a warm upstairs and a cooler downstairs in winter, and the reverse in summer. Causes include duct design, sun exposure, insulation and a single thermostat for the whole house. Possible fixes are balancing dampers, adding returns upstairs, sealing and insulating ducts, zoning dampers with two thermostats, a ductless mini split in the problem room and attic insulation. A technician can measure airflow and temperature in each room and recommend a combination that fits your home and budget. See duct services and ductless mini splits.
Heating Across Dallas Fort Worth
We repair and install heating systems in Dallas and the surrounding area, with teams in Fort Worth, Frisco and Southlake. See Fort Worth, Arlington, Frisco and Southlake. For emergencies, such as no heat in a freeze, email us with URGENT in the subject line or call, and we offer same day appointments wherever possible. Email service@plumberservicetx.com or call +1 (614) 756-0643.
Heat Pump vs Gas Furnace: Which Fits a North Texas Home?
| Factor | Heat pump | Gas furnace with AC |
|---|---|---|
| How it works | Moves heat in and out with refrigerant, cools and heats | Burns gas for heat, separate AC for cooling |
| Efficiency in mild weather | Very high, often 200 to 400 percent efficient in heating terms | 80 to 98 percent in heating terms |
| Performance in a hard freeze | Lower capacity as temperatures fall, backup heat may be needed | Strong heat regardless of outside temperature |
| Operating cost | Depends on electricity rates, often lower in typical winters | Depends on gas prices and electricity for the AC |
| Equipment count | One outdoor unit and one indoor unit | Furnace, AC condenser and coil |
| Gas required | No | Yes |
| Safety considerations | No combustion, no CO from the heating unit | Combustion needs venting, CO alarms and checks |
| Upfront cost | Often similar to or lower than furnace plus AC | Depends on the model |
| Lifespan | 12 to 15 years, as it runs year round | Furnace 15 to 20, AC 12 to 15 |
| Outages and generators | Needs a large generator for the strips and compressor | Furnace needs little power, which makes it easier to run on a generator |
Dual fuel systems pair a heat pump with a furnace, using each when it is most efficient. We calculate your options with your home’s loads, your utility rates and your priorities.
Furnace Efficiency, Venting and Gas Safety Details
- AFUE. Annual fuel utilization efficiency. An 80 percent furnace converts 80 percent of the gas to heat, and sends 20 percent up the flue. A 96 percent furnace sends 4 percent.
- Atmospheric venting. Older furnaces use hot flue gases rising through a metal vent. They need adequate combustion air and a vent that is intact.
- Induced draft furnaces. Use a fan to move flue gases through the heat exchanger and vent. Common in 80 percent furnaces.
- Condensing furnaces. Extract so much heat that flue gases condense. They vent in PVC, with a condensate drain, and often draw combustion air from outside.
- Combustion air. Furnaces in closets and small rooms need enough air, through louvers or ducts, for safe combustion.
- Gas pressure. Correct manifold pressure gives a stable flame and safe operation.
- Carbon monoxide. Test flue gas and ambient CO during service. Keep detectors working.
- Heat exchanger. Metal chambers that separate flame from house air. Cracks can leak combustion gases, and the furnace should be shut down if found.
Heating Costs and Savings Tips
- Seal air leaks around doors, windows, attic hatches and outlets on exterior walls.
- Insulate the attic, and the walls where possible. See attic insulation.
- Seal and insulate ducts. See duct services.
- Use a programmable or smart thermostat, and avoid large setbacks with heat pumps. See thermostats.
- Change filters regularly.
- Open curtains on sunny winter days, and close them at night.
- Use ceiling fans in reverse on low in rooms with high ceilings.
- Service the furnace annually.
- Close fireplace dampers when not in use.
- Consider an efficient heat pump or a high efficiency furnace when replacing.
What to Do If Your Heat Goes Out in a Freeze
- Check the thermostat, breaker and filter. Reset the furnace once.
- Call for service right away. Write URGENT in your email subject, and tell us the temperature and who is in the home.
- Close off unused rooms, and keep warm in one room with blankets and layered clothing.
- Open cabinet doors under sinks, and let faucets drip, to protect pipes. See burst pipe repair.
- Never use a gas oven, a charcoal grill or a generator indoors for heat.
- Use space heaters carefully, three feet from anything flammable, plugged into a wall outlet.
- Check on elderly and vulnerable neighbors.
- If it will be many hours, consider moving to a warmer location.
- If you lose power as well, a generator can restore heat. See generators.
Heating & Furnaces — Frequently Asked Questions
How do I know whether my furnace is 80 or 90 percent efficient?
Look at the vent. Metal vent pipes suggest 80 percent, PVC pipes suggest a condensing 90 percent plus. The label shows the AFUE.
What is auxiliary heat?
Electric heat strips that supplement a heat pump in very cold weather.
Is it okay to turn off my furnace in spring?
Yes. Replace the filter, and schedule maintenance. You can leave it on standby.
What does it mean when my furnace blows cold air?
The burner may not have lit, the flame sensor may be dirty, or the high limit may have shut it off. Check the thermostat fan setting, and call if the furnace does not light.
How do I reset my furnace?
Turn the power off at the switch for 30 seconds and back on, once. If it fails again, call.
Why is my heat pump running in the winter with cold air?
It may be in defrost mode or the system may be struggling. Brief cool air during defrost is normal.
Should I replace my furnace and AC at the same time?
If both are old, often yes, to save cost and match the system.
What is the rollout switch?
A safety device that shuts the furnace off if flames roll out of the burner area. It is a sign of a blocked vent or heat exchanger problem.
Why does my furnace smell when I first turn it on?
Dust that settled on the heat exchanger burns off, and the smell usually fades in a few hours. A persistent burning, chemical or gas smell needs attention.
How often should I change my furnace filter?
Every one to three months during the heating season, and more often with pets or dust.
Why does my furnace keep turning on and off?
A dirty filter, an overheating furnace, a bad flame sensor or an oversized unit can cause short cycling. A technician can find the cause.
Is it safe to use a space heater if my furnace is out?
Use only approved electric heaters, with care, and never gas stoves, ovens or outdoor heaters indoors. Follow safety rules, and call for repair.
Do I need to service a heat pump in winter?
A yearly tune up is recommended. Check the outdoor coil for ice and debris during cold weather.
What temperature should I set my thermostat in winter?
Many people choose 68 degrees when home and a few degrees lower when asleep or away. Avoid large swings on a heat pump.
How long does furnace installation take?
Typically a day, with more time for venting or ductwork changes.
Is a furnace covered by my home warranty?
It depends on your plan and the condition. Check the terms.
Why is my furnace not heating?
Common causes are a thermostat setting, a tripped breaker, a dirty flame sensor, a failed igniter or gas valve and a clogged filter. A technician can diagnose it safely.
How much does furnace repair cost in Dallas?
It depends on the failed part. Plumber Service TX gives a written flat rate quote after diagnosis, and you approve it before work begins.
How often should a furnace be serviced?
Once a year, ideally in fall before the heating season.
How long does a furnace last?
Often 15 to 20 years with maintenance.
Is a heat pump good in Texas?
Often yes. It heats and cools efficiently in the mild North Texas winter, with auxiliary heat for cold snaps.
What should I do if I smell gas near my furnace?
Leave the house, avoid switches and call Atmos Energy or 911 from outside.
Do you offer same day heating repair?
We offer same day appointments for urgent no heat calls wherever possible.
Can a furnace leak carbon monoxide?
A cracked heat exchanger or blocked vent can. Keep CO detectors on each level and have the system inspected yearly.
Need heating & furnaces in DFW today?
Email service@plumberservicetx.com and our dispatch team will confirm your same-day or next-day appointment window.