Serving Dallas–Fort Worth: Arlington · Fort Worth · Frisco · Southlake

service@plumberservicetx.com

Repiping · Dallas, TX

Repiping in Dallas, TX: Whole House and Partial Repipe

Replace failing pipes with PEX or copper, compare repair, reroute and repipe, and approve a written flat rate quote.

  • PEX & copper repipes
  • Most jobs done in days
  • Upfront flat-rate pricing
New PEX repipe manifold installed during a whole-home repipe in Dallas

Need it handled today? Call +1 (614) 756-0643 · book online by email

Quick answer

Repiping replaces the water supply pipes in your home, usually with PEX or copper, when old pipes leak repeatedly, corrode or deliver rusty water or low pressure. Consider it after two or more leaks in a short time, or when the home has galvanized steel, polybutylene or badly pitted copper. A repipe of a typical home takes a few days and is done with minimal wall openings. Plumber Service TX repipes homes across Dallas and Fort Worth, compares repair, reroute and repipe in a written flat rate quote, and pulls the permit where required.

Signs You May Need Repiping

  • Repeated pinhole leaks or leaks in different parts of the house
  • Rusty, brown or metallic tasting water
  • Low pressure at several fixtures
  • Galvanized steel pipes, common in older homes
  • Polybutylene pipe, a gray plastic used in some homes built from the late 1970s through the mid 1990s, which is known for failures
  • Green or blue corrosion on copper joints
  • Water bills that climb with no explanation, see leak detection

Repair, Reroute or Repipe?

OptionBest when
RepairOne leak, pipe otherwise sound
RerouteA single bad line, such as under a slab, replaced by a new line through walls or attic. See slab leak repair
Partial repipeOne zone has failing pipes, such as the kitchen and bath
Whole house repipeSeveral leaks, widespread corrosion, polybutylene or galvanized pipe

Need it handled today? Call +1 (614) 756-0643 · book online by email

PEX or Copper?

PEXCopper
InstallationFlexible, fewer fittings, fasterRigid, soldered joints
CostGenerally lowerGenerally higher
Freeze resistanceExpands slightly, less likely to burstMore likely to split
LifespanSeveral decades50 years or more in good conditions
Water quality concernsApproved for potable use, check local codeCan corrode in aggressive water

Both are widely used in Texas. We recommend based on your home, water chemistry and budget.

How a Repipe Works

  1. Inspection and a written quote with a fixture count and a plan.
  2. Permit and scheduling, with water shutoff times planned.
  3. New lines are run through attic, walls and crawl spaces, with small access openings.
  4. The new lines connect to fixtures, the water heater and the main.
  5. The system is pressure tested and inspected.
  6. Drywall patching is quoted separately or coordinated with a repair contractor.

Most homes are done in two to five days, depending on size and access. Homes on slab foundations have lines in the attic or walls, which is why a reroute or repipe avoids breaking the slab.

Does Insurance Cover Repiping?

Most homeowners policies do not pay to replace pipes because they are worn out, but they may cover damage from a sudden burst. Some insurers also charge more or limit coverage for homes with polybutylene or galvanized pipe. Ask your agent before you decide, and keep the inspection report, which supports a claim or a policy discount.

Repiping Across Dallas Fort Worth

We serve Dallas and the surrounding area, including Fort Worth, Arlington, Frisco and Southlake. Related: burst pipe repair and water quality. Email service@plumberservicetx.com or call +1 (614) 756-0643. Tell us the age of the home and the pipe material if you know it.

Why Pipes Fail: The Science Behind Repiping Decisions

Pipes do not last forever, and the reasons they fail help you decide when to replace them instead of patching.

Copper

Copper is long lived, but it can develop pinhole leaks from the inside through pitting corrosion, particularly with certain water chemistries, high flow velocity, or high chlorine. Type M thin wall copper installed in many homes is more susceptible than thicker type L. Flux residue and poor soldering can also cause failures at joints. Pinhole leaks usually appear first in one place, and then in others as the pipe ages. The pattern of repeated leaks is the sign.

Galvanized steel

Galvanized pipe is steel with a zinc coating. The zinc wears away, and the steel rusts from the inside. Rust builds up and narrows the pipe, which lowers water pressure and discolors water. Eventually the pipe leaks through. Homes built before the 1960s may still have galvanized pipe, often with steel at the connection to copper that has corroded.

Polybutylene

This gray plastic pipe was installed widely from the late 1970s to the mid 1990s. It is prone to brittle failure caused by oxidation from chlorine in the water, particularly at fittings. There were class action settlements, and many insurers will not cover homes with it or charge more. Replacement is widely recommended.

CPVC

Used for hot and cold water in many homes. It can become brittle with age and heat, and crack at fittings. A failure rate that increases after 20 to 30 years can justify replacement of an older system.

PEX

Modern, flexible and corrosion resistant. The main risks are installation errors, UV damage if exposed to sun, damage by rodents and fitting failures in some older brass fittings.

How to Decide: A Practical Repiping Checklist

FactorPoints toward repairPoints toward repiping
Number of leaksOne isolated leakTwo or more in a short period
Pipe materialCopper type L or PEX in good shapeGalvanized, polybutylene, thin type M copper with pits
Age of the homeUnder 30 years with good pipeOriginal pipes over 40 to 50 years old
Water qualityClean, steady waterRusty, discolored or metallic tasting water
Water pressureNormalLow at multiple fixtures with a clear cause in the pipes
Planned remodelNo plansWalls open, cheaper to replace now
Insurance and resaleNo issueInsurer requires or buyers worry
BudgetLimited, with a good short term repairAble to invest in a permanent fix

Repiping is a decision about the whole system, not the last leak. A camera inspection or a pressure test, plus a sample of the pipe where we open a wall, gives hard evidence.

What a Repipe Costs You and What It Saves

  • Cost drivers. House size, number of bathrooms and fixtures, pipe material, ceiling and wall access, and whether the home has a second story.
  • Savings on repeated repairs. A pipe with several leaks may cost more in repairs and water damage over a few years than a repipe would.
  • Water damage avoided. One burst can cost more than the repipe.
  • Insurance. Some insurers lower premiums or restore coverage after repiping a problem material.
  • Water pressure and flow. New pipes restore pressure and clean flow.
  • Resale. Buyers and inspectors react well to documented new plumbing.

We give a written flat rate quote based on a walk through, so you can compare it with the cost of repeated repairs.

The Repiping Process in Detail

  1. Inspection. We locate the main shutoff, the water heater, each fixture, the pressure and the pipe material. We check the attic, the crawl space and any wall access.
  2. Plan and quote. We design the layout of the new lines, usually a manifold or a trunk and branch system with PEX, or copper if chosen, and write the quote.
  3. Permit. A plumbing permit and inspections are normally required.
  4. Preparation. We protect floors and furniture, and set up water shutoff times. We install a temporary water supply for the home during the day if possible.
  5. Install new lines. New pipe is run through the attic, in walls and in crawl spaces, with small access holes in drywall, usually in closets, behind cabinets and in the garage.
  6. Connect fixtures. Each fixture gets a new supply line and shutoff, and the water heater connection is updated.
  7. Test. The system is flushed and pressure tested, and inspected by the city.
  8. Patch and clean up. We patch holes to a paint ready stage, or coordinate a drywall contractor, and clean the work area.
  9. Remove or abandon old pipe. Old lines are cut off and capped or removed where practical.

PEX Systems: Manifold or Trunk and Branch

PEX can be installed in two main layouts, and each has pros and cons.

Home run manifold

A central manifold, near the water heater or in a closet, has a shutoff for each line, and a separate PEX line runs to each fixture. Pros: individual shutoffs for each fixture, steady pressure when several run at once, fewer joints in walls. Cons: more pipe used, a longer wait for hot water at distant fixtures, and larger access needs.

Trunk and branch

Larger trunk lines run through the house with branches to fixtures, like traditional plumbing. Pros: less pipe, faster hot water delivery with a good layout. Cons: more fittings, and pressure may vary when fixtures run at the same time.

Both are acceptable. We suggest a layout for your house, with hot water recirculation if the runs are long. PEX types A, B and C differ in flexibility, fitting systems and cost, and type A with expansion fittings is popular for its strength and fitting reliability.

Copper Repiping

Copper remains an excellent choice for those who prefer a metal system, higher fire resistance and decades of proven performance. Type L is the standard, with press fittings or soldered joints. Press fittings are faster and avoid open flame in tight spaces. Copper is rigid, so routes need more planning, and it costs more in material and labor. In areas with aggressive water, copper may corrode, so water chemistry matters. We discuss the water conditions in your area and your priorities, and quote both PEX and copper where it makes sense.

Living Through a Repipe

A repipe is disruptive, but it is manageable with a plan.

  • Expect a crew on site for one to five days, depending on the size of the house.
  • Water is off for periods, often during working hours, and restored in the evening where possible.
  • Plan for toilets, drinking water and cooking. Fill containers beforehand.
  • Clear access to closets, attics, crawl spaces and the water heater.
  • Move fragile items from walls and shelves near where we will work.
  • Expect dust and some noise. We cover floors and clean daily.
  • Secure pets and keep children away from the work area.
  • Tell us about any special needs, such as medical equipment that needs water.

Repiping Slab Homes: Reroute vs Replace Under the Slab

In many Dallas homes, some supply lines run under the slab. When those lines leak, a repipe usually abandons the under slab lines and runs new pipe through the attic or walls. This avoids breaking concrete and removes the buried pipe from the equation. The old under slab pipe is capped at both ends and left in place. The new overhead lines are accessible and easy to repair in the future. For homes with a single slab leak, a partial reroute might be enough. See slab leak repair for the options and costs.

Water Pressure, Regulators and Expansion Tanks During a Repipe

A repipe is the best time to fix the pressure side of your plumbing. We test incoming pressure, install or replace the pressure reducing valve to keep pressure in the safe range, add an expansion tank at the water heater if the system is closed, replace the main shutoff with a full port ball valve, and add accessible shutoffs for fixtures and zones. Water hammer arrestors can be added to quick closing valves. These small upgrades protect the new system for decades.

Insurance, Resale and Disclosure

  • Tell your insurer you have repiped, and ask for a premium review, especially if you had polybutylene or galvanized pipes.
  • Keep the invoice, the permit and the inspection sign off. They prove the work.
  • When selling, disclose the pipe history and provide the documents. New plumbing is a selling point.
  • If you are buying a home with problem pipe, use the inspection to negotiate the cost of repiping.
  • Ask about transfer of any workmanship warranty to the next owner.

Questions to Ask a Repiping Contractor

  • What material do you recommend and why? Can you quote both PEX and copper?
  • How will you route the lines, and how many access holes will you need?
  • Who patches drywall, and is it included?
  • How many days will the water be off each day?
  • Do you pull the permit, and will it be inspected?
  • What is the warranty, on materials and on labor?
  • Will you test pressure, replace the regulator, and add shutoffs?
  • Who is on the crew, and are they licensed?

Real Repiping Scenarios in North Texas

A 1980s home with polybutylene

A family bought a 1985 house in Arlington, and the inspection noted gray polybutylene supply lines. The insurer asked for replacement within a year. A whole house PEX repipe ran new lines through the attic with a manifold near the water heater, with small access holes in closets. The homeowners kept living in the house, and the insurer restored standard coverage after the permit sign off.

A 1960s home with galvanized pipes

A home in East Dallas had brownish water and weak pressure at the second floor bathroom. Pipes were galvanized steel, clogged with rust inside. A repipe restored flow and clear water, and the water heater performed better with unrestricted flow.

A 1990s Plano home with copper pinholes

Three pinhole leaks in 18 months, each in a different wall, led a homeowner to ask about repiping. Testing showed thin wall copper with pits. A partial repipe of the hot lines and a pressure regulator replacement ended the leaks, and the homeowner chose to repipe the cold lines later during a remodel.

A slab leak home with several leaks

A Fort Worth home with copper under the slab had leaked twice. A reroute through the attic removed the under slab lines, so no slab breaking and no repeat. See slab leak repair.

Planned Repiping vs Emergency Repiping

PlannedAfter a failure
Water damageNonePossible and often costly
Choice of materials and layoutFull choiceLimited by urgency
SchedulingYour preferred datesFast, sometimes disruptive
Price comparisonMultiple quotesLittle time
Coordination with remodelingPossibleOften not
StressLowHigh

If your pipes are the problem type, planning is almost always the better route. We give you an honest estimate of remaining life when we inspect.

Repiping Warranty and Documentation

New pipe has two warranties. The manufacturer typically covers the pipe and fittings against defects for many years, sometimes decades. The installer’s warranty covers workmanship, such as leaking joints, poor routing and damage during installation. Ask for both in writing, along with the permit record, the inspection sign off, a diagram of where manifolds and shutoffs are, and the product names and sizes. Keep them in a folder and give them to the next owner.

Common Repiping Myths

Myth: Repiping tears up the whole house

Modern repiping uses small access holes in closets, attics and behind fixtures. Most of the work is in the attic or crawl space, and patches are small and easy to paint.

Myth: Copper always lasts a lifetime

Copper can last 50 years or more, but thin wall pipe with aggressive water can fail early. The pattern of leaks tells the story.

Myth: PEX is cheap and weak

PEX is widely used in new construction and proven. Quality of fittings and installation matter more than the label.

Myth: A single repair is always cheaper

If the pipe is failing, repairs repeat, and total cost plus water damage often exceeds repiping.

Myth: Repiping is only for old homes

Some homes from the 1980s and 1990s have problem materials, and some newer homes have installation defects or aggressive water.

Myth: Plastic pipe affects water taste

Potable rated PEX and CPVC are approved for drinking water. A brief taste after installation fades after flushing.

How to Prepare Your Home for a Repipe

  1. Clear closets, cabinets under sinks and the garage near the water heater.
  2. Make attic and crawl space access easy, and tell us about hazards such as pests.
  3. Take down pictures and fragile items from walls.
  4. Arrange for pets, and plan meals around the water outages.
  5. Photograph the condition of walls and floors before we start.
  6. Tell your HOA if rules apply, and your insurer if required.
  7. Be ready to approve the final layout of manifolds and shutoffs before we close up.

Water Quality and Pipe Material Interactions

Water chemistry affects how long pipes last. Low pH or soft water can be more aggressive toward copper, while hard water scales and narrows pipes. High chlorine or chloramine levels contribute to the degradation of some plastics and rubber parts. Dissolved oxygen, high temperature and high velocity speed corrosion. Utilities treat water to limit corrosion, with pH adjustment and corrosion inhibitors, and your plumbing is designed with those conditions in mind. Homes with softeners should check that the treated water does not attack copper and brass. If you see blue green stains, pinhole leaks or metallic taste, have the water tested. The result informs whether you should choose PEX instead of copper, add treatment or adjust settings. We discuss this with homeowners who have had repeat pinhole leaks.

Choosing materials for your water

  • PEX is immune to corrosion, and a good choice for aggressive water.
  • Copper does well in most municipal water. Type L is thicker than M.
  • CPVC resists corrosion, but is brittle with age and heat.
  • Brass fittings can dezincify in some conditions, so choose dezincification resistant fittings.
  • Stainless steel is used in special cases.

Repiping Questions Answered

Will the new pipes change my water pressure?

Pressure is mostly determined by the supply. New, smooth pipe flows better than corroded pipe, so you may notice improvement.

Can PEX be used outdoors?

It must be protected from sunlight. Buried or insulated lines are fine.

Will repiping affect my water heater?

New connections are made, and codes require certain parts, such as shutoffs and expansion tanks.

Do I need to flush the new lines?

Yes. We flush them, and tell you to run taps for a few minutes after the first use.

Can I choose where manifolds and shutoffs go?

Yes. Tell us your preferences. Accessible locations help later.

Repiping in Dallas, TX — Frequently Asked Questions

Will my appliances need new connectors after a repipe?

Often we replace connectors and shutoffs at the same time, for reliability.

Does repiping increase the chance of leaks right after installation?

Pressure testing before closing walls finds problems, so leaks after installation are rare.

Can you repipe in the winter or summer?

Yes. Summer attic work is done early in the day to keep crews safe, and winter work is planned around freezes.

Do I need to replace the water heater with a repipe?

Not necessarily, but the repipe is a good time to inspect it, replace connectors and valves, and add an expansion tank.

How do I know if my house has polybutylene pipes?

Look at pipes near the water heater, the main shutoff or under sinks. Gray flexible plastic with markings such as PB2110 indicates polybutylene.

Can pinhole leaks be repaired instead of repiping?

Yes, individually, but they tend to recur as the pipe ages. Two or more in a short time points toward repiping.

Will repiping fix my rusty water?

If the rust comes from galvanized pipes, yes. If it comes from the water heater or the utility, a different fix is needed. We test.

Is it okay to mix PEX and copper?

Yes, with the right transition fittings. Many repipes connect new PEX to existing copper at the water heater and stubs.

Can I repipe only the hot water lines?

Yes, if the cold lines are in good shape. Hot lines often fail first, because heat accelerates corrosion. We check both.

Does repiping improve water pressure?

Often, if the old pipes were narrowed by rust or scale. Pressure also depends on the supply and regulator.

Is it okay to leave old pipe in the wall?

Yes, when it is disconnected, drained and capped, and removal would damage the structure.

How long does a repipe last?

PEX and copper both last decades. Many manufacturers cite 50 years or more, depending on conditions.

Will my water taste different after repiping?

Water may taste metallic or like plastic briefly. Flush the lines, and it should clear.

How do I know my pipe material?

Copper is reddish brown, galvanized is gray and magnetic, polybutylene is gray plastic, and PEX is colored red, blue or white. A plumber can identify it.

Can I live in the house during a repipe?

Usually yes, with some planning for water outages and dust.

Does a repipe require a permit?

Yes, with inspections.

Is there a good time of year to repipe?

Any time, though avoiding extreme heat in attics helps the crew work safely, so spring and fall are often ideal.

How much does repiping a house cost in Dallas?

It depends on the size of the house, the number of fixtures, the pipe material and access. Plumber Service TX gives a written flat rate quote after inspection, and you approve it first.

When should I repipe my house?

After repeated leaks, with galvanized or polybutylene pipe, or with rusty water and low pressure from corrosion.

How long does repiping take?

Most homes take two to five days.

Is PEX or copper better for repiping?

Both work well. PEX is faster and usually less expensive, while copper is rigid and long lasting. The choice depends on the home and water.

Will I have water during repiping?

Water is off during working hours. We plan shutoffs, and many homes have water restored each evening.

Do I need a permit for repiping in Dallas?

Usually yes, with an inspection. Your plumber should pull it.

Does repiping increase home value?

It can reduce risk for buyers and insurers, especially if it replaces polybutylene or galvanized pipe.

Can I repipe only part of my house?

Yes. A partial repipe replaces a failing zone, but it leaves old pipe elsewhere, which may fail later.

Need repiping in Dallas, TX today?

Email service@plumberservicetx.com and our dispatch team will schedule a whole-home assessment and flat-rate quote.