Plumbing · Dallas–Fort Worth, TX
Bathroom Remodeling in Dallas, TX: Remodel Plumbing Done Right
Rough in, fixtures and permits for bathroom and kitchen remodels, with a written flat rate quote based on your plans.
- Licensed & insured
- Upfront flat-rate pricing
- Same-day appointments
Need it handled today? Call +1 (614) 756-0643 · book online by email
Quick answer
A bathroom remodel in Dallas needs a plumber early, not after the tile is chosen. Plumbing decides where the toilet, vanity, shower and tub can go, so the rough in work for supply lines, drains and vents happens right after demolition, before walls close up, and fixtures are set at the end. Moving a toilet or shower drain costs far more than keeping them in place. Plumber Service TX handles the plumbing for bathroom and kitchen remodels across Dallas and Fort Worth, pulls permits where required and gives a written flat rate quote before work begins.
Where Plumbing Fits in a Bathroom Remodel
- Plan. Decide on fixture locations, shower type, tub, vanity size and any moves. Confirm the drain and vent routes.
- Demolition. Remove old fixtures, walls and flooring.
- Rough in plumbing. New supply lines, drains, vents and shower valves are installed and pressure tested.
- Inspection. Where a permit is required, the rough in is inspected before walls close.
- Walls, waterproofing and tile. Other trades finish the room.
- Fixture installation. Toilet, vanity, faucets, shower trim, tub and accessories are set, tested and sealed.
- Final inspection and punch list.
What Costs More: Moving Plumbing or Keeping It
| Change | Effect on plumbing cost |
|---|---|
| Replace fixtures in the same place | Lowest |
| Move a vanity a few feet | Moderate |
| Move a toilet or shower drain on a slab | High, because concrete must be cut and the drain rerouted |
| Convert a tub to a walk in shower | Moderate, new drain and valve height |
| Add a second sink or bathroom | High, new supply, drain and vent |
| Switch to a tankless or larger water heater | Moderate to high |
Most Dallas homes sit on slab foundations, so drain moves involve cutting the slab. Ask for the plumbing cost of each layout before you commit.
Need it handled today? Call +1 (614) 756-0643 · book online by email
Kitchen Remodel Plumbing
- Sink and faucet relocation and new supply lines
- Garbage disposal, dishwasher, ice maker and pot filler connections
- Gas line for a range or cooktop. See gas line services
- New shutoff valves and drain venting
- Water filtration tap. See water quality
- Island sinks need special venting
Plumbing Fixture Choices That Affect the Work
- Shower valves. Pressure balanced or thermostatic, and rough in depth.
- Shower drains. Linear drains and curbless showers need slope planning.
- Toilets. Match the rough in, usually 12 inches. See toilet repair and installation.
- Faucets. Hole count and mounting style must fit the vanity.
- Water heater capacity. Body sprays and soaking tubs need more hot water.
Permits for Remodel Plumbing in Dallas
Moving drains, adding fixtures or bathrooms, and gas work normally need a permit and inspection. Replacing a faucet or toilet in the same place usually does not. Texas plumbers are licensed by the Texas State Board of Plumbing Examiners, and we pull permits where required, so the inspection record is in place when you sell the home.
Remodel Plumbing Across Dallas Fort Worth
We serve Dallas and the surrounding area, including Fort Worth, Arlington, Frisco and Southlake. Related: plumbing fixtures and repiping. Email service@plumberservicetx.com or call +1 (614) 756-0643. Send your plans, photos and fixture list for a quote.
Plan the Plumbing Before You Choose Finishes
The most expensive remodeling mistakes come from choosing finishes before the plumbing layout is settled. A tile pattern, a vanity or a freestanding tub may not fit where the pipes can reasonably go. A good sequence is to decide the layout, confirm the plumbing plan and its cost, and then choose fixtures and finishes that fit.
Bring us in at the design stage. A plumber can read a floor plan and tell you which moves are simple and which are costly, point out where a wall might hide a stack or a main, and check that the water heater can supply the new fixtures. That conversation often saves more than it costs, and it avoids change orders after demolition begins.
Questions to settle early
- Will any fixture move? If so, how far, and what is below or above it?
- Are you adding a bathroom or a second sink?
- What type of shower: tub shower combo, walk in shower, curbless or steam?
- Do you want a freestanding tub, and is the floor structure strong enough?
- Will the water heater keep up with the new fixtures?
- Do you need a new gas line, for a range or a fireplace?
- Do the walls and floor have room for the new drains and vents?
Rough In Plumbing Explained
Rough in is the stage where the pipes are installed inside the walls, floors and ceilings before they are closed up. It has three parts.
Drain, waste and vent
Every fixture needs a drain sized for its flow and a vent to let air in. Toilets need a three or four inch drain, showers and tubs two inches, and sinks one and a half to two inches. Drains must slope about a quarter inch per foot toward the stack, so a fixture cannot be moved far without rework. Vents must connect to the vent system, which rises through the roof.
Supply
Hot and cold supply lines connect to each fixture, with shutoff valves. Shower valves, tub spouts and spout heights are set at specific dimensions that depend on the valve brand and the finish thickness. Pipes in exterior walls should be insulated to avoid freezing.
Special items
Gas lines for ranges, dryers and fireplaces, a water line for refrigerators and ice makers, pot fillers, bidets and filtered water taps, and drains for floor drains and washing machines.
After rough in, the plumbing is tested under pressure, and the inspector verifies it before the walls close. Fixing a mistake after drywall is far more expensive than before.
Slab Foundations and Moving Drains
Most Dallas homes sit on concrete slabs, and drain lines run below the floor. Moving a toilet, shower or tub means cutting the slab, trenching, laying new pipe with the correct slope, and patching with concrete. The cost depends on how far you move the drain, the thickness and reinforcement of the slab, and the access to the existing line. Cutting post tension cables in slabs is a serious hazard, so the slab must be scanned first. A good plumber will use a scan, or a ground penetrating radar, before cutting.
Alternatives to moving the drain include keeping the fixture where it is and changing the surroundings, raising the floor to run the drain above the slab, or using an up flushing toilet system in limited cases. Each has trade offs in cost, noise and resale. We lay these out so you can decide with the numbers in front of you.
Shower Options and Their Plumbing Needs
| Shower type | Plumbing needs | Things to plan |
|---|---|---|
| Tub shower combo | Standard valve, tub spout, two inch drain | Simplest and cheapest. Needs access panel behind the valve |
| Walk in shower with a curb | New drain location, pan and waterproofing, valve | Slope and waterproofing are critical |
| Curbless shower | Recessed floor, linear or center drain | Needs the floor framing or slab lowered, or the floor around raised |
| Steam shower | Steam generator, dedicated electrical circuit, sealed enclosure | Needs a vapor tight enclosure and a drain |
| Body sprays and multiple heads | Larger supply lines, diverters, more flow | Check water heater capacity, pressure and flow |
| Handheld on slide bar | A wall supply elbow and a diverter | Adds accessibility |
Waterproofing is not plumbing, but plumbing and tile work depend on it. A leak behind a shower wall causes expensive damage, so we pressure test and flood test the pan before tile goes down.
Kitchen Remodel Plumbing in Detail
Sink and faucet
Moving the sink changes the drain, vent and supply. An island sink needs a loop vent or an air admittance valve in some jurisdictions. Check local code.
Dishwasher
Needs a hot water supply, a drain connection with a high loop or air gap and an electrical connection. Make sure the drain is correct, so the dishwasher does not back up into the sink.
Disposal
Needs a switch or an air switch and a location for the outlet. See plumbing fixtures.
Refrigerator water line
A quarter inch line with a shutoff. Use braided or copper lines, not cheap plastic.
Gas range or cooktop
Needs a correctly sized gas line, a shutoff and a connector. A change from electric to gas requires a plan and a permit. See gas line services.
Pot filler
A cold water line to a wall mounted faucet above the range, with a shutoff valve in an accessible place.
Water filtration and instant hot
An RO system, a filtered tap or an instant hot water dispenser need electrical outlets, drains and supply lines. See water quality.
Water Heater Capacity for a Remodeled Home
A remodel can add fixtures that strain an existing heater. A large soaking tub can hold 60 to 80 gallons. Body sprays can use ten gallons per minute or more. A tank heater sized for a smaller house runs out in the middle of a shower. We calculate the demand and recommend a bigger tank, a tankless unit, or a second heater near the new bathroom. A recirculation pump helps with the wait for hot water in a long run. See tank water heaters and tankless.
Permits and Inspections for Remodel Plumbing
The City of Dallas and most cities require permits for new plumbing, moving fixtures and drains, adding bathrooms, and new gas lines. Replacing fixtures in the same location typically does not. The permit brings a rough in inspection before walls close and a final inspection when the work is done. Homeowners sometimes try to skip permits to save money, but unpermitted work can cause problems with insurance claims, resale, and safety. Texas plumbers are licensed by the Texas State Board of Plumbing Examiners, and a licensed plumber must pull the permit for plumbing work. We pull the permit, schedule inspections and keep the record, so you have it when you sell.
Coordinating With Your Remodeler
Plumbing is one of several trades, and it works best when the schedule is clear.
- Pre construction meeting with the remodeler, the plumber and the electrician to confirm layouts and dimensions.
- Demolition exposes what is really in the walls. Unexpected findings, such as old galvanized pipe, are discussed immediately.
- Rough in installs pipes, followed by inspection.
- Insulation, drywall, waterproofing and tile by other trades.
- Trim out by the plumber installs fixtures, faucets and the toilet.
- Final inspection and punch list. Leaks, drips and adjustments are fixed.
We work with your general contractor, or with you directly if you manage the project. We confirm the fixture specs and rough in dimensions in writing, and order long lead items early.
Hidden Problems Found During Remodels
- Corroded galvanized or old copper pipe. Replace while the walls are open. See repiping.
- Cast iron drains with cracks or heavy scale. A good time to replace the section.
- Missing or improper vents from earlier work that cause slow drains.
- Leaks behind old tubs and showers that rotted the framing.
- Polybutylene or other problem materials. Replace.
- Unpermitted prior plumbing that has to be corrected to pass inspection.
- Slab cracks or settlement that affect drain slope.
We report each finding with photos and a written change quote, so there are no surprises in the final bill.
Bathroom Remodel Plumbing Cost Drivers
- Layout changes. Moving a drain is the single biggest variable.
- Number of fixtures. More sinks, showers and tubs, more rough in.
- Fixture selection. High end valves, wall mount faucets and custom drains cost more.
- Floor type. Slab, pier and beam, or second floor framing affect access.
- Age of existing plumbing. Old pipes may need replacement.
- Permit and inspection fees.
- Water heater and gas upgrades.
- Finish coordination. Tile thickness and wall depth affect valve and trim position.
We provide a written flat rate quote based on the plans, and any change during the job is quoted in writing before we do it.
Accessible and Aging in Place Remodels
A remodel is the right time to add features that help people stay safe at home. Plumbers help with comfort height toilets, curbless showers with enough floor slope, handheld showers, thermostatic or pressure balancing valves to prevent scalding, wide doorways for plumbing equipment, lever style fixtures, and blocking and supply lines for grab bars. A roll in shower needs a larger drain and a linear drain, and the floor must be built or lowered for a smooth transition. We coordinate with occupational therapists or designers when needed, and follow accessibility guidelines for dimensions and heights.
Outdoor Kitchens, Laundry Rooms and Other Remodels
- Outdoor kitchens. Need a water supply, a drain, gas for grills and burners, and freeze protection. A permit is usually required.
- Laundry rooms. Need washer boxes, a standpipe drain, a utility sink and a dryer vent, and in some homes a gas line.
- Wet bars and butler’s pantries. Small sinks, ice makers and wine coolers with water lines.
- Garage conversions and additions. Need new supply and drain connections, and often a new water heater.
- Guest houses and ADUs. A separate sewer connection or tie in, with proper slope and cleanout.
- Pools and spas. Equipment pads, gas heaters and backflow preventers.
Remodel Plumbing Timelines
| Project | Typical plumbing time | Notes |
|---|---|---|
| Fixture swap in the same place | Half a day to a day | No permit in most cases |
| Bathroom remodel, fixtures stay | One to two days in total across rough in and trim | Valve replacement adds time |
| Bathroom remodel, drains move | Three to five days, plus slab work and curing | Slab cutting, trenching and patching |
| New bathroom addition | Several days over rough in and trim | New supply, drain, vent and permits |
| Kitchen remodel with island sink | Two to four days | Vent and drain planning |
| Whole house remodel | Several weeks across phases | Coordinated with the construction schedule |
These are working times, not calendar times. Inspections, material delivery and other trades set the overall schedule. We give you a window and keep to it where we can.
Choosing Plumbing Fixtures for a Remodel
- Buy fixtures early. Rough in dimensions depend on the exact model.
- Match valve and trim brands. Trim kits fit only their own valves.
- Check fixture specs. Spout reach, faucet hole count and sink dimensions must work together.
- Consider water use and pressure. Large rain heads and body sprays need adequate supply.
- Choose finishes that hold up. PVD and similar finishes resist wear and hard water.
- Plan for parts availability. A brand with long term support helps repairs decades later.
- Keep paperwork. Save invoices, model numbers and warranty documents in one place.
Remodeling Plumbing in Older Dallas Homes
Older neighborhoods have charm and surprises. Cast iron drains in a 1950s bungalow may be intact or may be corroded. Galvanized supply lines may be mostly rust inside. Bathrooms may have been added at different times with different materials, vents may be missing, and walls may hide old repairs. A remodel is a chance to bring the plumbing up to modern standards, and a good plumber inspects before quoting so the numbers include likely upgrades. Where the budget is tight, we help you prioritize safety and reliability items first, such as replacing failing supply lines and fixing venting, and leave cosmetic items for later.
Historic homes may have rules about visible changes, including fixtures, and some neighborhoods have design review. Check before you order fixtures.
Budgeting the Plumbing Side of a Remodel
Plumbing is a smaller share of most remodel budgets than cabinets, tile or appliances, but it has the most surprises. A realistic plan separates the costs into four buckets.
- Known work. Rough in for the layout you have drawn, fixtures you have chosen, permits and inspection.
- Likely extras. New shutoffs and supply lines, a pressure regulator, an expansion tank, and replacement of old valves.
- Contingency. Ten to twenty percent for what the open walls reveal, such as rotted framing, corroded pipe or incorrect venting.
- Fixtures and finishes. The choices you control, where small decisions add up.
Ask each contractor to price the same scope, with fixture allowances and clear exclusions. A price that leaves out the permit, the slab work or the fixtures is not comparable to one that includes them. We write an itemized quote, and a change order for anything that changes.
Protecting Your Remodel After It Is Done
- Test every fixture and shutoff before the final payment.
- Ask for the location of every shutoff valve, drawn on a sketch.
- Keep leftover tile, caulk and spare parts for future repairs.
- Install leak sensors under new sinks and by the toilet and water heater.
- Save manuals, model numbers and warranty cards.
- Schedule a plumbing check after the first month, and again at the first year, when small issues show up.
Kitchen & Bathroom Plumbing — Frequently Asked Questions
Should I buy fixtures myself or have the plumber supply them?
Either works. Buying them yourself gives control of style and price, and having us supply them gives one point of responsibility for fit and warranty.
What is a change order?
A written change to the original scope and price, agreed before extra work is done.
Can I live in my home during a bathroom remodel?
Usually, if there is another bathroom. We try to keep water available for the rest of the house.
Should the plumber or the tile installer go first?
The plumber does rough in before the walls close, the tile installer finishes the surfaces, and the plumber returns for trim out.
Can you install a bidet or a bidet seat?
Yes. A bidet seat needs a cold water tee and an outlet. A separate bidet needs hot and cold supply and a drain.
How do I choose between a tub and a walk in shower?
It depends on use, resale and space. Showers are easier to enter and often preferred for aging in place, while a tub appeals to families with young children and some buyers.
Do I need a plumber before the demolition starts?
Yes. A plumber can tell you what is behind the walls, confirm the plan and shut off and cap lines safely before demolition.
How long does bathroom rough in plumbing take?
Typically one to three days for a standard bathroom, and longer if a slab must be cut.
Can I reuse my existing shower valve?
Sometimes, if it is in good condition and the trim kit is available. Many remodels replace it for better function and a matching trim.
What is an air admittance valve?
A one way valve that lets air into a drain line without a vent through the roof. Allowed in some places, but not all, and not for every use.
How do I know if my slab has post tension cables?
Many newer slabs do. The slab must be scanned before cutting. A plumber will not cut blind.
Should I replace old pipes during a remodel?
Usually yes, if they are corroded or a known problem material. The wall is already open, so the cost is lower.
Can you install a freestanding tub?
Yes, with floor support, a floor mounted or wall mounted filler, and a drain that matches the tub.
Does a remodel require a new water heater?
Not always, but added fixtures may exceed capacity. We calculate it.
What is a rough in inspection?
An inspection by the city of the pipes and tests before the walls close.
Do you coordinate with my contractor?
Yes. We work with your general contractor, designer or you directly.
Do I need a plumber for a bathroom remodel in Dallas?
Yes, for any move of drains, supply lines, shower valves or gas, and for installing fixtures correctly. A licensed plumber also pulls permits.
How much does remodel plumbing cost?
It depends on the layout, whether drains move, and the fixtures. Plumber Service TX gives a written flat rate quote based on your plans, and you approve it before work begins.
When does the plumber come in a remodel?
For rough in right after demolition and before walls close, and again for fixtures at the end.
Does moving a toilet cost a lot?
On a slab foundation it can, because the concrete must be cut and the drain rerouted. Keeping it in place is the least expensive option.
Do remodels need permits?
Moving or adding plumbing usually does. Same place fixture swaps usually do not.
Can you convert a tub to a shower?
Yes. It needs a new drain connection, shower valve and waterproofing by the tile contractor.
Should I replace old supply lines during a remodel?
Usually yes. Open walls are the cheapest time to replace old or corroded lines and shutoffs.
How long does remodel plumbing take?
Rough in for a typical bathroom takes one to three days, and fixture installation about a day.
Need kitchen & bathroom plumbing in DFW today?
Email service@plumberservicetx.com and our dispatch team will confirm your same-day or next-day appointment window.