Serving Dallas–Fort Worth: Arlington · Fort Worth · Frisco · Southlake

service@plumberservicetx.com

Electrical · Dallas–Fort Worth, TX

LED and Recessed Lighting Installation in Dallas, TX

Plan and install recessed lights, pendants, dimmers and LED upgrades, with a written flat rate quote first.

  • Licensed & insured
  • Upfront flat-rate pricing
  • Same-day appointments
Layered kitchen lighting — recessed ambient, island pendants and under-cabinet task light

Need it handled today? Call +1 (614) 756-0643 · book online by email

Quick answer

LED lighting installation in Dallas replaces older fixtures and bulbs with efficient LEDs, and adds recessed lights, under cabinet lighting, pendants, dimmers and smart controls. Recessed lighting is installed by cutting holes in the ceiling and wiring to a switch, and in insulated ceilings it needs IC rated housings. LED lighting uses far less electricity than incandescent bulbs and lasts many years. Plumber Service TX installs indoor lighting across Dallas and Fort Worth, with a lighting layout and a written flat rate quote you approve before work begins.

Indoor Lighting Projects We Install

ProjectBest for
Recessed lights (can lights)Even, clean overhead light in kitchens, living rooms, hallways
LED retrofit and fixture replacementCutting energy use and replacing dated fixtures
Pendants and chandeliersOver kitchen islands, dining tables and entries
Under cabinet lightingTask light on kitchen counters
Dimmers and smart switchesMood, savings and remote control
Closet, pantry and stair lightsSafety and convenience
Additional switches and circuitsFixing awkward layouts

Planning Recessed Lighting

  • Spacing. Space lights about half the ceiling height apart, and about 2 to 3 feet from walls, adjusted for the layout.
  • Size. 4 inch and 6 inch housings are common, with slim wafer lights for tight ceilings.
  • Brightness and color. Lumens set brightness, and 2700 to 3000 K gives warm light, while 4000 K is brighter and cooler.
  • IC rating. Required in insulated ceilings to contact insulation safely.
  • Dimming. Use compatible LED dimmers to avoid flicker.
  • Attic access. Access above makes installation easier and cleaner.

Need it handled today? Call +1 (614) 756-0643 · book online by email

How Installation Works

  1. Walk through, plan the layout and choose fixtures.
  2. Written quote and a permit where required.
  3. Turn off power, cut openings and run cable, with small patches kept to a minimum.
  4. Install housings, fixtures and switches or dimmers.
  5. Test, adjust and clean up, and show you the controls.

Drywall repair and paint after the installation are quoted separately or coordinated with a finishing contractor. See also ceiling fan installation and outdoor lighting.

Lighting Installation Across Dallas Fort Worth

We serve Dallas and the surrounding area, including Fort Worth, Arlington, Frisco and Southlake. Related: electrical services. Email service@plumberservicetx.com or call +1 (614) 756-0643.

Lighting Design Basics: Three Layers

Good lighting is more than a ceiling full of bulbs. Designers plan three layers that work together, and a room feels right when all three are present.

Ambient lighting

General illumination that fills the room, from recessed lights, ceiling fixtures, ceiling fans with lights, cove lighting or wall sconces. It sets the overall brightness so you can move around safely.

Task lighting

Focused light for activities such as cooking, reading, grooming and working. Examples are under cabinet lights in kitchens, vanity lights in bathrooms, pendant lights over islands and desks, and reading lights in bedrooms. Task lighting should be bright, glare free and placed where shadows do not fall on your work.

Accent lighting

Highlights features such as artwork, architecture, shelves, fireplaces and landscaping. Examples include picture lights, track lights, in cabinet lights and toe kick lights.

Layered lighting, with dimmers, lets you shape a room for different uses, from bright for cleaning, to soft for dinner. We help you plan where each layer goes, and what controls make it easy to use.

Understanding LED Specifications

SpecificationWhat it meansGood choices
LumensThe amount of light, not wattsLiving room 1,500 to 3,000 total for 200 square feet, kitchen higher, bedrooms lower
Color temperature in KelvinWarmth or coolness of the light2700 to 3000 K warm white for living areas and bedrooms, 3500 to 4000 K neutral for kitchens and workspaces
CRI, color rendering indexHow accurately colors look90 or higher for kitchens, baths, closets and art
Beam angleThe spread of lightWide for general lighting, narrow for accents
DimmabilityWhether it works with a dimmerMatch LED and dimmer types to avoid flicker
Efficacy in lumens per wattEfficiency80 to 120 or more for good LEDs
Rated lifeHours before output falls to about 70 percent25,000 to 50,000 hours
ENERGY STAR or similar certificationTested quality and efficiencyPrefer certified products

Recessed Lighting: A Detailed Guide

Housings and trims

New construction housings are installed before the ceiling is closed. Remodel or old work housings install from below through a hole in finished drywall. Slim LED wafer lights have a built in driver and need no housing, and they suit ceilings with limited space and attics with limited access. Trims include baffle trims to reduce glare, reflector trims for brightness, gimbal trims that tilt, and adjustable and wall wash trims for accents.

Insulation and heat

Housings in insulated ceilings must be IC rated, meaning they can be in contact with insulation. Air tight rated housings prevent conditioned air from leaking into the attic. Non IC housings need clearance from insulation and may be a fire risk if covered.

Layout rules of thumb

  • Space lights about half the ceiling height apart. For an 8 foot ceiling, about 4 feet.
  • Place lights 2 to 3 feet from walls for wall washing, or farther for general light.
  • In kitchens, place lights over counters and the sink, not directly over the center of the room only.
  • Avoid placing lights directly above a bed or a TV, where glare is annoying.
  • In hallways, a single row down the center usually works.
  • Balance the number of lights with brightness. Many dimmer lights are better than a few bright ones.

Wiring

Lights wire in groups called runs, on one or more switches or dimmers. We plan circuits to keep loads within the breaker rating, and use connected, accessible junction boxes.

Kitchen, Bathroom and Bedroom Lighting Plans

Kitchen

A combination of recessed or ceiling lights for ambient light, under cabinet LEDs for tasks, pendants over the island or the sink, and possibly in cabinet lights or toe kick lights for accent. Use 3000 to 4000 K, CRI 90 or more. Provide separate switches or dimmers for each layer.

Bathroom

Even, shadow free light on the face, from sconces on both sides of the mirror, or a lit mirror, plus ceiling lights. Use damp or wet rated fixtures near showers, with GFCI protection on circuits. A night light on a motion sensor helps.

Bedroom

Soft ambient light with dimmers, bedside lamps or sconces, and closet lighting. Warm color temperatures, 2700 K, and avoid glare.

Living and family rooms

Ambient light from recessed lights or fixtures, plus table and floor lamps, accent lights for art or shelves, and dimmers on all circuits.

Home office

Bright, glare free light, 3500 to 4000 K, with task lighting, and minimized screen glare.

Garage and utility areas

High output LED shop lights with durable fixtures, motion sensors, and switches near entrances.

Dimmers, Smart Switches and Controls

  • Dimmers. Match the dimmer to the lights. LED compatible dimmers, often called CL dimmers or LED rated, prevent flicker and buzzing. Check the maximum load, and the minimum load, since LEDs draw little power.
  • Smart switches and dimmers. Control lights by phone or voice, with schedules and scenes. Many need a neutral wire in the switch box. Older homes may lack it. Some use no neutral designs.
  • Occupancy and vacancy sensors. Turn lights on or off with motion, useful in closets, laundry rooms, garages and bathrooms.
  • Timers and photocells. For outdoor and security lighting.
  • Multi location switching. Three way and four way switches let you control one light from several places, such as at the top and bottom of stairs.
  • Lighting scenes. Preset levels for movies, dinners and cleaning, controlled by a keypad or an app.
  • Whole home lighting control. Integrated systems for large homes and new construction.

Lighting Upgrades That Save Energy and Money

Lighting accounts for around 10 percent of a typical home’s electricity use, and LED technology cuts that sharply compared with incandescent and compact fluorescent lamps. A 60 watt equivalent LED uses about 8 to 10 watts. Replacing 30 old bulbs can save a noticeable amount each year, depending on use. LED bulbs also last 15,000 to 50,000 hours, which means years of use without a change, and they produce little heat, which lowers cooling load in a Texas summer. The cost of LED bulbs has dropped, and the payback is often within a year or two.

  • Start with the lights you use most, such as kitchens, living rooms and outdoor lights.
  • Choose ENERGY STAR certified bulbs and fixtures.
  • Match color temperature across a room, so the light looks consistent.
  • Use dimmers and occupancy sensors to reduce hours of use.
  • Check the enclosure rating. Enclosed fixtures need LED bulbs rated for them, or they overheat.
  • Recycle old bulbs properly. Compact fluorescents contain mercury.
  • Use LED fixtures with integrated light sources for recessed and under cabinet lighting.

Under Cabinet, Cove and Specialty Lighting

Under cabinet lighting

LED strips or bars under kitchen cabinets illuminate counters and reduce shadows. Hardwired versions give the cleanest look, and plug in versions are easy. Choose high CRI, a warm to neutral color temperature, and dimmable products. Wiring runs from a switch or a transformer hidden in a cabinet.

Cove lighting

LED strips hidden in a ledge near the ceiling wash light up the wall and ceiling, creating a soft glow. Used in living rooms, bedrooms and theaters.

Toe kick and stair lights

Low level lights help with safety and add ambiance at night.

Closet and pantry lights

Motion activated LED fixtures turn on when you open the door.

Picture and display lights

Accent art and collectibles with focused LEDs and controlled beams.

Decorative fixtures

Chandeliers, pendants and sconces add style. Heavy fixtures need proper support in the ceiling, such as a rated box or a brace. Mounting height matters: chandeliers over a dining table usually hang 30 to 36 inches above the table.

Vanity lighting

Sconces at eye level on both sides of the mirror produce even light, and a bar above the mirror works if it is wide and bright.

Lighting Problems and Fixes

ProblemLikely causeFix
A light does not turn onBulb, switch, wiring, breaker or a failed driverReplace the bulb, test the switch, check connections
Flickering LEDsIncompatible dimmer, loose neutral, poor quality bulbsChange the dimmer or the bulbs, check connections
Buzzing from a dimmer or a lightDimmer mismatch, loose partsReplace with a compatible dimmer
Bulbs burn out quicklyHigh voltage, heat, loose sockets, wrong bulb typeCheck voltage, use rated bulbs, replace sockets
Recessed light keeps turning offThermal protector from overheating or insulation contactUse an LED retrofit, improve clearance
Switch gets hotOverload, loose connectionTurn off and call an electrician
Lights dim when appliances startOverloaded circuit, loose neutralHave the circuit checked
Lights stay faintly lit when offSwitch leakage with LEDs, wiringUse an LED compatible switch, or a bleeder

Lighting Installation Process: What to Expect

  1. Walk through. We look at the rooms, the ceilings, the attic access, the existing wiring and the switch locations.
  2. Plan the layout. We mark fixture locations with tape, and discuss brightness, color and controls. Mock ups help you see it.
  3. Written quote. It lists the fixtures, the controls, the wiring, patching and any permits.
  4. Preparation. We protect floors and furniture, and turn off power.
  5. Rough in. Cutting openings, running cable and mounting housings or boxes.
  6. Install fixtures and controls. Connections, dimmers, switches and trims.
  7. Test. We check every light and control, and adjust beams.
  8. Patch and clean. Drywall repair and painting are coordinated, or done by a partner.

Indoor Lighting Across Dallas Fort Worth

We install and upgrade lighting in Dallas and the surrounding area, with teams in Fort Worth, Frisco and Southlake. See Fort Worth, Arlington, Frisco and Southlake. Related services: ceiling fans, outdoor lighting and electrical services. Email service@plumberservicetx.com or call +1 (614) 756-0643. Send photos of the rooms, the fixtures you like and the ceiling type.

Switches, Circuits and Wiring Plans for Lighting

Lighting depends on the switches that control it. Planning circuits and switches properly makes a home easy to use. Here are the common arrangements.

Switch typeWhat it doesWhere it is used
Single poleControls a light from one locationMost rooms
Three wayControls a light from two locationsHallways, stairs, large rooms with two doors
Four wayAdds a third or more locations, between two three way switchesLarge open areas
DimmerAdjusts brightnessLiving areas, dining rooms, bedrooms
Occupancy sensorTurns lights on and off with presenceClosets, laundry, garages, bathrooms
Vacancy sensorYou turn it on, it turns off when the room is emptyBedrooms, offices
Timer switchTurns off after a set timeFans, outdoor lights
Smart switchApp and voice control, scenes, schedulesAny room
Keypad controlPreset scenes for a room or the houseGreat rooms, media rooms

Neutral wires matter for smart switches and many dimmers. In older homes, switch boxes may lack a neutral, since the wiring was run to the light and not the switch. An electrician can add a neutral, or select a switch that does not need one.

Retrofit Lighting: Upgrading Old Fixtures and Bulbs

  • Swap bulbs for LEDs. The simplest step. Choose the same base and shape, and select color temperature and brightness.
  • Retrofit recessed cans. LED retrofit kits screw into the existing socket, with a trim that seals the opening. They avoid cutting new holes.
  • Replace fluorescent fixtures. Kitchen and garage fluorescent boxes can be replaced with LED panels or strips.
  • Update old dimmers. Old dimmers were designed for higher loads and may cause flicker.
  • Replace builder grade fixtures. New fixtures can change the look and use less energy.
  • Add lighting where there is none. Under cabinet, closets, stair lights.
  • Add controls. Motion sensors and smart switches reduce waste.
  • Remove hazards. Replace damaged sockets, brittle wires and unsafe fixtures.

Lighting and Human Comfort: Color, Glare and Sleep

Light affects mood, alertness and sleep. Cooler, bluer light in the morning and daytime supports alertness, and warm, dim light in the evening supports sleep. Many people use warmer lights in bedrooms and living areas, and cooler, brighter lights in kitchens, garages and workspaces. Some smart bulbs and systems adjust color temperature through the day. Avoid glare, which strains the eyes, by using diffused fixtures, indirect light and shielded bulbs, and by placing lights away from direct sight lines. For older adults, brighter and more even lighting helps vision and reduces fall risk, and night lights along the path to the bathroom help. For screens, reduce contrast between the screen and the surrounding room. For people with sensitivities to flicker, choose high quality, flicker free LEDs, and avoid cheap drivers.

Lighting Costs and Payback

  • Bulbs. An LED bulb costs more than an old bulb but pays back in months in energy savings and lasts years.
  • Fixtures. Basic LED fixtures are affordable. Decorative and designer fixtures cost more.
  • Installation. Replacing a fixture is simpler than adding a new light. New recessed lights need cutting, wiring and patching.
  • Controls. Dimmers and smart switches add moderate cost, and add flexibility.
  • Savings. Switching a typical household’s bulbs to LEDs can reduce lighting energy by about 75 percent.
  • Maintenance savings. Fewer bulb changes, particularly in high ceilings.
  • Rebates. Some utilities discount LED purchases.

We give a written flat rate quote after a walk through, with each fixture, switch and control itemized, so you can decide what to do now and what to do later.

Lighting for Texas Homes: Heat, Windows and Daylight

North Texas homes get strong sunlight, and many have large windows and covered patios. Lighting design should work with daylight. Rooms that get bright afternoon sun may feel glaring, and rooms on the north side may need extra light in the day. Use window treatments, such as shades and films, to control glare and heat, and use dimmable lights to balance the light as daylight changes. LED lighting produces little heat, which helps keep summer cooling costs down. Recessed lights in insulated ceilings need to be sealed to stop air leaks into the attic, and IC rated for contact with insulation. In rooms with high ceilings, consider fixtures with strong output and long life, since changing bulbs is a chore. In outdoor rooms and patios, use damp or wet rated fixtures. Maximize daylight with light colored walls and ceilings, and layer artificial light to fill in after sunset.

Lighting that helps you sell your home

Bright, even, warm lighting makes rooms look larger and more welcoming in photos and showings. Updating dated fixtures, replacing burned out bulbs with matching color temperature, and adding recessed lights in key rooms are inexpensive improvements. Buyers notice dim kitchens and dark hallways.

Lighting Installation Checklist

  1. List the rooms and the goals for each.
  2. Photograph the rooms in day and at night.
  3. Choose fixtures and bulbs by style, color temperature and brightness.
  4. Decide on switches, dimmers and smart controls.
  5. Check the attic or ceiling access.
  6. Plan for patching and painting.
  7. Ask about permits for new circuits.
  8. Schedule installation, and prepare the rooms.
  9. Test lights and controls with the installer.
  10. Keep spare bulbs, manuals and warranty information.

Indoor Lighting Installation — Frequently Asked Questions

How do I keep recessed lights from letting air into the attic?

Use air tight rated housings and seal the trim, or choose sealed LED wafer lights.

Can lights be installed in a finished ceiling without attic access?

Yes, with careful cutting and fishing wire, though it takes more time.

Can LED lights be used in enclosed fixtures?

Only if they are rated for enclosed fixtures. Heat shortens their life otherwise.

What is a lumen?

A measure of brightness. More lumens mean a brighter light.

How do I choose between a ceiling light and recessed lights?

A ceiling fixture is simple and decorative. Recessed lights give a clean look and more even light, with added installation work.

Should I put all lights on dimmers?

In living areas, bedrooms and dining rooms, yes. In utility spaces, switches or sensors are fine.

Can I replace incandescent fixtures with LED?

Yes. Replace the bulbs with LED, or install LED fixtures. Check dimmer compatibility.

How long do LED fixtures last?

Often 25,000 to 50,000 hours, which is 10 to 20 years of typical use.

Do I need a licensed electrician for lighting?

For new wiring, new circuits and fixtures that require wiring changes, yes. Simple bulb changes do not.

What is the best color temperature for a kitchen?

3000 to 4000 K, with high CRI.

Can I add lights without opening walls?

Often yes, with surface mounted fixtures, plug in lights or fishing wires through attic space.

How many recessed lights do I need in a room?

A rough rule is one light per 4 to 6 square feet, and it depends on ceiling height and the brightness of each light. We plan it with a layout.

Why do my LED lights flicker or buzz?

An incompatible dimmer, a loose connection, a low quality driver or a load that is too small for the dimmer. Matching parts fixes it.

What is the difference between 2700 K and 4000 K?

2700 K is warm, similar to incandescent. 4000 K is neutral to cool, brighter and more energizing.

Can I install recessed lights in a ceiling with no attic access?

Yes, with remodel housings or wafer lights, cut through drywall, and wire fished through the ceiling.

Do LED bulbs save money?

Yes. They use a fraction of the energy and last many years.

Can you replace my old fixtures with new ones?

Yes. We install fixtures you choose, check the box and support and wire them safely.

Do I need a permit for lighting work?

New circuits and major work may need one. Fixture swaps often do not.

Can I use smart bulbs with dimmers?

Not usually. Use smart bulbs on a switch left on, or use smart switches instead.

How much does LED lighting installation cost in Dallas?

It depends on the number of fixtures, ceiling type and wiring. Plumber Service TX gives a written flat rate quote, and you approve it before work begins.

How many recessed lights do I need?

About one per 4 to 6 square feet in the main areas, adjusted for ceiling height and use. We lay it out on a plan.

Can you add recessed lights without attic access?

Yes, with fishing wires and small openings, though it takes more time.

Do LED lights save money?

Yes. They use much less electricity than incandescent bulbs and last many years.

What color temperature should I choose?

2700 to 3000 K is warm and common in living areas. 3500 to 4000 K is brighter for kitchens and work areas.

Why do my LED lights flicker?

Incompatible dimmers, loose connections or low quality drivers. We match compatible parts.

Do I need a permit for lighting?

New circuits and major work usually need one. Simple fixture swaps often do not.

Can you install smart lighting?

Yes, including smart switches, dimmers and bulbs.

Need indoor lighting installation in DFW today?

Email service@plumberservicetx.com and our dispatch team will confirm your same-day or next-day appointment window.